Born SFP Transceiver – Born Electronics

BT-SFP-DAC-10G-2M

admin — Thu, 22 Aug 2024 12:42:41 +0000

SFP+ Direct Attach Cables are compliant with the SFF-8431, SFF-8432 andSFF- 8472 specifications. Various choices of wire gauge are available from30 to 24AWGwith various choices of cable length (up to 7m).

BT-SFT-IGRJ45

admin — Thu, 22 Aug 2024 06:43:25 +0000

BT-SFT-IGRJ45 Copper Small Form Pluggable (SFP) transceivers is high performance, cost effective module compliant with the Gigabit Ethernet and 1000BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supporting 1000Mbps data- rate up to 100meters reach over unshielded twisted-pair category 5 cable. The module supports 10/100/1000Mbps auto negotiation data- links when the SFP interface support SGMII also. The module provides standard serial ID information compliant with SFP MSA, which can be accessed with address of 0xA0- 0xA2 via the IIC BUS protocol.

BT-SFT-GRJ45-CS

admin — Thu, 22 Aug 2024 06:01:34 +0000

BT-SFT-GRJ45 10/100/1000 BASE-T copper SFP transceiver is high performance, cost effective module compliant with the Gigabit Ethernet and 1000BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supporting 1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cable. The BT-SFT-GRJ45 supports1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modulation (PAM) signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The BT-SFT-GRJ45provides standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2-wire serial CMOS EEPROM protocol. The physical IC can also be accessed via 2-wire serial bus at address ACh.

BT-QSFP-M03

admin — Tue, 20 Aug 2024 11:55:13 +0000

Support 40GBASE-SR4/QDR application
ComplianttoQSFP+ElectricalMSASFF-8436
Multirateofupto10.3125Gbps
Transmissiondistanceupto150m(OM3) and 300m (OM3) optional
+3.3V single power supply
Low power consumption
OperatingcasetempCommercial:0°Cto+70°C
RoHS6/6compliant

BT-SFP-S20-11GCS

admin — Tue, 20 Aug 2024 11:22:25 +0000

BT-SFP-S20-11GCS is a high performance, cost effective modules, which is supporting up to 10.3125Gbps, and transmission distance up to 20km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a laser driver and a 1310nm DFB laser. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA) and a Limitting Amplifier. The module is hot pluggable into the 20- pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100Ohms differential impedance and AC coupled in the module. The optical output can be disabled by LVTTL logic high-level input of TX _ DIS. Transmit Fault (Tx _ Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX _ LOS) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.

BT-QSFP-S10-40G

admin — Tue, 20 Aug 2024 11:15:54 +0000

BT-QSFP-S10-40G Transceiver is a high performance, cost effective module for serial optical data communication applications to 41.5Gb/s.TheQSFP-40G-LR4 is designed to 40GBASE-LR4of the IEEE P802.3ba standard for 10kmlinks. The module converts 4 inputs channels (ch) of 10Gb/s electrical data to 4 CWDM optical signals, and multiplexes them into a single channel for40Gb/s optical transmission. Reversely, on the receiver side, the module optically de-multiplexes a40Gb/s in put into 4 CWDM channels signals, and convertsthemto4 channel output electrical data. The central wavelengths of the 4 CWDM channels are 1271, 1291, 1311 and 1331 nm as members of the CWDM wavelength grid defined in ITU- TG.694.2.Itcontains a duplex LC connector for the optical interface and a 38-pin connector for the electrical interface. To minimize the optical dispersion in the long- haul system, single-mode fiber (SMF) has to be applied in this module.

BT-SFP-G20-AB

admin — Tue, 20 Aug 2024 08:35:35 +0000

BT-SFP-G20-AB is a high performance, cost effective modules, which is supporting up to 1.25Gbps, and transmission distance up to 20km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a laser driver and a 1310nm FP laser. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA) and a Limitting Amplifier. The module is hot pluggable into the 20- pin connector. The high-speed electrical interface is based on low voltage logic, with nominal 100Ohms differential impedance and AC coupled in the module.

The optical output can be disabled by LVTTL logic Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.

BT-SFP-G120-1.25G

admin — Thu, 08 Aug 2024 12:58:01 +0000

BT-SFP-G120-1.25G is a high performance, cost effective modules, which is supporting up to 1.25Gbps, and transmission distance up to 120km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a laser driver and a 1550nm DFB laser. The receiver section consists of a APD photodiode integrated with a transimpedance preamplifier (TIA) and a Limitting Amplifier. The module is hot pluggable into the 20- pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100Ohms differential impedance and AC coupled in the module.

The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Transmit Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.

BT-SFP-G80-1.25G

admin — Thu, 08 Aug 2024 11:18:16 +0000

BT-SFP-G80-1.25G is a high performance, cost effective modules, which is supporting up to 1.25Gbps, and transmission distance up to 80km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a laser driver and a 1550nm DFB laser. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA) and a Limitting Amplifier. The module is hot pluggable into the 20- pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100Ohms differential impedance and AC coupled in the module.

The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Transmit Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of the receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.

BT-SFP-G20 SFP Module

admin — Thu, 08 Aug 2024 10:46:09 +0000

BT-SFP-G20 is a high performance, cost efective modules, which is supporting up to 1.25Gbps, and transmission distance up to 20km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a laser driver and a 1310nm FP laser. The receiver section consists of a PIN photodiode integrated with a tran- simpedance preamplifier (TIA) and a Limitting Amplifier. The module is hot pluggable into the 20-pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100Ohms diferen- tial impedance and AC coupled in the module.

The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Transmit Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser oper- ation or safety. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and con- figuration data via the 2-wire SFP Management Interface. This inter- face uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.